
Industrial gearboxes and screw jacks
TMP screw jacks, worm, bevel-helical and helical gearboxes in catalogue versions or modified to your requirements. The TS 031 444 and TSN 030 444 worm gearboxes are proven designs from ZŤS and SJT Moldava, made by us under their original designation. Bevel-helical and helical gearboxes came later – not every drive can be solved with a worm.
Four types – depending on what the drive has to do
A screw jack turns rotation into linear motion. For the others, the shaft arrangement and the ratio you need decide. We will fine-tune the rest together.
TMP screw jacks
Lift, push and tilt – motor-driven or by hand, on their own or in a system. Translating or rotating screw, full catalogue online.
More
Worm gearboxes
Shafts at right angles, offset. High ratio in a small housing, quiet running, any mounting position. The TS 031 444, TSN 030 444 and ZAP have full online catalogues.
More
Bevel-helical gearboxes
The drive turns through 90° while efficiency stays high. One- and two-stage versions.
More
Helical gearboxes
In-line shafts for simple, reliable speed reduction. One- and two-stage versions.
MoreComparison at a glance
| Type | Shaft arrangement | Ratio | When to choose it |
|---|---|---|---|
| TMP screw jack | right angle to screw | 1 or 0.25 mm / rev | lifting and pushing up to 210 kN |
| Worm | right angle, offset | 10 – 100 | high ratio, little space, quiet running |
| Bevel-helical | right angle | 7.5 – 180 | 90° drive with high efficiency |
| Helical | in-line | 2.5 – 31.5 | simple in-line speed reduction |
TMP screw jacks and TS 031 444, TSN 030 444 and ZAP worm gearboxes have full online catalogues – see below. We will gladly send you parameters of the other types, dimension drawings and data sheets – just tell us the type or the application.
Four catalogues, no PDF
Every page has its own address, can be printed and is found by search engines. Same look, same navigation – in Slovak, English and German.
TMP screw jack catalogue
Types N, VS, RS and 4VS, dimensions, accessories, sizing, installation and ordering code. On dimension pages, just click a size.
Open the TMP catalogue
TS 031 444 worm gearbox catalogue
Ratings and torques for ratios 10 – 80, dimensions, IEC motor flange, mounting options, mounting positions, lubrication, ordering code and old designations.
Open the TS catalogue
TSN 030 444 geared motor catalogue
Speeds and torques for ratios 10 – 80, dimensions with and without foot, ten shaft end positions, installation, lubrication and ordering code.
Open the TSN catalogue
ZAP worm gearbox catalogue
Ratings for ratios 10 – 100, dimensions with and without motor, eleven mounting options, mounting positions, lubrication, spare parts and ordering code.
Open the ZAP catalogue
From casting to gearbox
Nine stops in our workshop – from a lump of cast iron to a pallet ready for dispatch. With some swarf and no studio lighting.
See the photo storyWhat to send us so we choose right
The more of this list you send, the fewer questions we have to ask back. But even one line is a good start.
- motor power and speed
- required output speed or gear ratio
- output torque, if you know it
- mounting position and fixing method
- operating conditions – duty cycle, shocks, environment
- quantity and delivery date
- when replacing an old gearbox – a photo of the nameplate
A gearbox from ZŤS or SJT Moldava? We know it well.
In 2008 we took over the complete production programme of SJT Moldava. That is why we make new parts and complete replacements for gearboxes with a ZŤS or SJT Moldava nameplate – and repair even the ones that remember the 1970s.
Frequently asked questions
Do you make gearboxes in small quantities?
Yes. We produce anything from a single unit to a series – catalogue versions as well as modifications for a specific machine.
Do you have a PDF catalogue?
The catalogues of TMP screw jacks, TS 031 444 worm gearboxes, TSN 030 444 geared motors and ZAP worm gearboxes are online – print any page or save it as PDF straight from your browser (Ctrl + P). For the other types we send data sheets by e-mail.
Can you replace an old ZŤS or SJT Moldava gearbox?
In most cases, yes – we took over the SJT Moldava programme in 2008. Send us a photo of the nameplate and the connection dimensions and we will tell you whether it needs a new gearbox, a repair or just new parts.
Can the gearbox operate in any position?
TS 031 444 and TSN 030 444 worm gearboxes work in any mounting position. For the other types, we take the position into account in the design (lubrication, venting).
Not sure which type is right?
Send us the motor power and the required output speed – we will choose for you. No obligation, and no lecture on gear geometry unless you want one.