TMP worm gear screw jacks with trapezoidal lead screws ready for dispatch
Worm gear screw jacks · 5 – 210 kN (0.5 – 21 t)

TMP screw jacks

Linear drives for controlled lifting, pushing and tilting. Six sizes from 5 to 210 kN (0.5 – 21 t) – by motor or by hand, alone or in a synchronised system.

Principle

What moves: the screw or the nut

The input shaft with the worm turns the worm wheel. Either the wheel has an internal thread and drives the screw axially (N, VS, 4VS), or it is fixed to the screw and turns it – then a nut travels along the screw (RS).

TMP N · VS · 4VS

Translating screw

The screw extends and retracts through the gearbox and lifts the load directly. It is secured against turning by the machine (N), a key in the gearbox (VS) or a square cover (4VS). It needs space below the gearbox.

N and VS dimensions in the catalogue →
TMP RS

Rotating screw with travelling nut

The screw is fixed to the worm wheel and only rotates. The load is carried by an LM, ERM or LRM nut that travels up and down the screw. Ideal where there is no space below the gearbox.

RS dimensions in the catalogue →
How they work

A worm, a screw and a little physics

The drive combines a worm gear with a trapezoidal lead screw. Both are right-hand as standard; left-hand is available on request. The screw is supplied in the length you need.

TMP units work in any position, alone or linked into a system. Mechanical connection with connecting shafts ensures precise synchronised lifting even when each jack carries a different load.

Self-locking: TMP 80 is self-locking at rest, TMP 32 – 71 conditionally, TMP 25 is not. Standard units are not dynamically self-locking – with vibration or shocks we recommend a brake on the input.

Connection: electric, servo, pneumatic or other motors can be mounted directly. Version S with a free input shaft can also be operated by hand – with a handwheel or crank. On request the units are prepared for inductive or incremental limit and speed sensors. Max. worm shaft speed is 2,800 rpm.

Also known as: worm gear screw jacks, machine screw jacks or mechanical actuators – in German Spindelhubgetriebe, in Slovak zdvižné prevodovky.

Section through a TMP screw jack – worm gear and lead screw
Sizes

Choose the size by force

Size = worm gear centre distance in millimetres. The deciding factor is the highest axial force per unit. The range covers 5 to 210 kN – loads of roughly 0.5 to 21 t.

TMP screw jack size range from TMP 25 to TMP 80

Each size has its own catalogue page with dimensions, a drawing and ready motor combinations.

Family photo

Big brother, little brother

The difference isn't just size, it's strength too – the little one lifts half a tonne, the big one 21 tonnes. Besides the colour, they share the same principle.

TMP 80 and TMP 25 screw jacks in the standard blue
On request

Blue is standard. Not compulsory.

On request we paint TMP units in other shades too – light grey or black, for example, to match the machine they go into.

For the food industry we supply a version with food-grade paint and food-grade grease.

TMP screw jacks in light grey paint on a pallet

Technical data

ParameterTMP 25TMP 32TMP 45TMP 63TMP 71TMP 80
Max. lifting force F [kN]5102550100210
Equivalent load approx. [t]0.512.551021
Lead screw (trapezoidal)Tr 18×4Tr 20×4Tr 30×6Tr 40×7Tr 55×9Tr 80×10
Housing materialAlAlGG20GG20GG20GGG40
Gear ratio SP / L4:1 / 16:14:1 / 16:16:1 / 24:17:1 / 28:19:1 / 36:110:1 / 40:1
Efficiency SP / L [%]32 / 2630 / 2429 / 2227 / 2122 / 1719 / 14
Max. input torque [Nm]3.37.1183893148
Max. lifting speed SP [mm/min]2,8002,8002,8002,8002,8001,500
Max. standard stroke [mm]7001,0001,3001,3001,3001,300
Weight at 0 mm stroke [kg]1.22.16173263
Weight per 100 mm stroke [kg]0.350.450.71.223.3

Al – aluminium alloy · GG20 – grey cast iron · GGG40 – ductile iron. Longer strokes on request (screw length up to 6,000 mm). More data (no-load torques, radial forces, motor combinations) on the Technical data catalogue page.

Applications

Lift, push, tilt

TMP units are used wherever a load must be moved along a straight line precisely and safely – with one drive or several at once.

Lifting

Lifting and work platforms, height adjustment of tables, conveyors and workstations.

Pushing

Moving slides, doors and covers, repositioning stops and tools.

Tilting

Tilting platforms, chutes, flaps and structures around a pivot.

Synchronised lifting

Several drives linked by shafts lift a large surface evenly – even under uneven load.

A series of TMP screw jacks before painting

One-off or series

We machine the housings, cut the gears and assemble the drives in one workshop. That is why we can supply the catalogue standard as well as a version adapted to your machine.

Send a TMP enquiry

Also available on request

When the standard is not enough, we design a custom solution. For example

  • ball screw versions NB, RSB, 4VSB
  • screws in C45 steel or 1.4301 stainless steel
  • left-hand lead screws
  • other gear ratios and modifications
  • preparation for inductive position sensors
  • safety nuts LM-B1 and LM-B2
  • bevel gearboxes for linked systems
  • screws longer than standard – up to 6,000 mm
  • other paint colours, food-grade paint and grease
  • 3D models in STEP format for your CAD
Catalogue online

The complete TMP catalogue – 31 pages, no PDF

Every page has its own address and can be printed. On dimension and accessory pages, just click a size – the drawing and table switch automatically.

Overview

  1. 01TMP 25 – 80 worm gear screw jacks – series overview
  2. 02TMP screw jacks – types N, VS, RS, 4VS and gear ratios
  3. 03TMP worm gear screw jacks – technical data

Sizes

  1. 04TMP 25 worm gear screw jack – 5 kN (0.5 t)
  2. 05TMP 32 worm gear screw jack – 10 kN (1 t)
  3. 06TMP 45 worm gear screw jack – 25 kN (2.5 t)
  4. 07TMP 63 worm gear screw jack – 50 kN (5 t)
  5. 08TMP 71 worm gear screw jack – 100 kN (10 t)
  6. 09TMP 80 worm gear screw jack – 210 kN (21 t)

Dimensions and versions

  1. 10TMP screw jack dimensions – types N and VS
  2. 11TMP screw jack dimensions – type RS (rotating screw)
  3. 12TMP 80 screw jack dimensions – type 4VS
  4. 13TMP screw jacks with input shaft (S) or motor (E)
  5. 14TMP screw jack lead screw ends G, S, D, T

Accessories

  1. 15TMP screw jack accessories – overview
  2. 16BL – mounting bars for TMP screw jacks
  3. 17KA – trunnion adapter for TMP screw jacks
  4. 18KAP – compact trunnion adapter for TMP screw jacks
  5. 19GK – clevis for TMP screw jacks
  6. 20GF – rod end for TMP screw jacks
  7. 21BP – mounting plate for TMP screw jacks
  8. 22LM – flange nut for TMP screw jacks
  9. 23ERM – cylindrical nut with keyway for TMP screw jacks
  10. 24LRM – cylindrical nut for TMP screw jacks
  11. 25GP – support bearing for TMP screw jacks
  12. 26Safety nuts LM-B1, LM-B2 and bellows MA
  13. 27Position sensors for TMP screw jacks – IS, AS, NC

Sizing and operation

  1. 28Screw jack calculation – duty cycle, torque, self-locking
  2. 29Screw jack lead screw – critical speed and buckling
  3. 30Screw jack installation, lifting systems and maintenance

Ordering

  1. 31TMP screw jack ordering code

TMP – frequently asked questions

How do I choose the right TMP size?

The size is determined by the highest axial force per unit. Then check force and speed against the duty cycle, check screws under compression for buckling, and keep the screw speed of type RS below 80 % of critical. The five-step procedure is on the catalogue pages Sizing and Critical speed and buckling – or send us load, stroke and speed and we will choose for you.

Are TMP screw jacks self-locking?

At rest, TMP 80 is self-locking, TMP 32 to 71 conditionally and TMP 25 is not. Standard units are not dynamically self-locking. If the load must not drop even under vibration, use a brake on the input – we are happy to specify one.

Can several TMP units be linked to lift synchronously?

Yes. The units are linked with connecting shafts and, where needed, bevel gearboxes. The mechanical connection ensures synchronised lifting even with uneven loads at individual points.

How long can the stroke be?

The standard stroke is up to 700 mm for TMP 25, 1,000 mm for TMP 32 and 1,300 mm for the larger sizes. On request we supply screws up to 6,000 mm long – under compression, buckling must be checked.

Can you supply TMP with a motor?

Yes. We supply TMP without a motor or as a complete unit with an electric motor; servo and pneumatic motors can be fitted too. Ready motor combinations are on the catalogue pages of each size.

Can a TMP screw jack be operated by hand?

Yes. In version S the TMP has a free input shaft to which a handwheel or crank can be fitted. It suits applications where the position is adjusted only occasionally and there is no power to hand. Dimensions are on the page Versions S and E.

How much does a TMP screw jack cost and when can you deliver?

Price and lead time depend on size, type, screw length, accessories and quantity. Send us an enquiry with load, stroke and speed – we will send you a quote with price and delivery date.

Screw jack or hydraulic cylinder?

A screw jack needs no power pack, hoses or oil circuit, positions very finely (0.25 mm per worm revolution with ratio L), and several units linked by shafts move in exact sync. Hydraulics are faster and more compact at very high forces. The comparison is in the article Screw jack or hydraulic cylinder?

Send us the load, stroke and speed

We will propose the TMP size and ratio – and tell you whether you need a brake or can rely on physics.